Elevate

Welcome to the Juniper Elevate Community

hero image

Popular Topics

Ask AI TechPost Feature Friday Routing Training and Certification Switching Junos OS See More

Featured Post

Promoted

Promo tile background

Check out the new TechPost 

Bits and Bytes Articles on Automated WAN Solutions, from Network Engineers to Network Engineers.

Browse Posts

Latest Discussions

  • Profile Picture

    RE: Apstra Error Codes

    By: IMAM PURWO HADI , 13 hours ago
    Posted in: Junos OS

    depend on your template configuration, in freefrom we can custom what configuration template base on Jinja Template. can you share what error after commit check and what you using template configuration? Thanks Imam Hadi ------------------------------ IMAM PURWO HADI --------------------------- ...

  • Profile Picture

    RE: IPSEC Tunnels up but no traffic is going to the ...

    By: fb35523 , 20 hours ago
    Posted in: SRX

    In general, an st0.x interface needs to be added to a security zone and have "family inet" configured on it (no IP address needed, but could be). set security zones security-zone vpn interface st0.4 You don't need any "host-inbound traffic" for the st0.4 interface, but if you have an IP on it, you ...

  • Profile Picture

    RE: Q in Q tunnel on QFX

    By: Olivier Benghozi , yesterday
    Posted in: Switching

    I guess you forgot: set interfaces xe-0/0/0 native-vlan-id 1 And you should probably: set vlans qinq-100 switch-options no-mac-learning At the NNI, you will receive double-tagged frames (maybe the laptop doesn't like them). ------------------------------ Olivier Benghozi ----- ...

  • Profile Picture

    RE: Q in Q tunnel on QFX

    By: nurairtt , yesterday
    Posted in: Switching

    We connected the laptops for testing. Customer switch was not connected. Switch model is qfx5120 running 23.4R2. Below is the applied configuration, set interfaces xe-0/0/0 flexible-vlan-tagging set interfaces xe-0/0/0 encapsulation extended-vlan-bridge set interfaces xe-0/0/0 unit 100 ...

  • Profile Picture

    RE: Q in Q tunnel on QFX

    By: Olivier Benghozi , yesterday
    Posted in: Switching

    you cannot really rely on the in/out bytes/packets values per unit on EX/QFX did you try with two real devices at each side ? maybe post the actual real content of both interfaces and vlan definition and what is the model of the switch btw? ------------------------------ Olivier Benghozi - ...

  • Profile Picture

    RE: Q in Q tunnel on QFX

    By: nurairtt , yesterday
    Posted in: Switching

    Hi Oliver, Thanks for your continuous support. We applied the recommended configuration changes and connected a test laptop to the UNI port while generating continuous ICMP requests. Both the UNI and NNI ports successfully learned the MAC addresses. However, we observed that the UNI port received ...

  • Profile Picture

    RE: encapsulation dix in encapsulation flexible-et ...

    By: DANIEL NG , yesterday
    Posted in: Routing

    apparently the vlan id is tagged since encapsulation flexible-ethernet-services requires flexible-vlan-tagging, which in term requires a vlan id. however, you can use encapsulation dix without vlan id when you don't have encapsulation flexible-ethernet-services. but then what is the difference ...

Latest Articles

  • Posted to: TechPost Blogs

    The SRX4700 100Gbps Full Duplex IPSEC tunnel TechPost demonstrates the ability of the HPE Juniper Networking flagship 1RU firewall device to encrypt 100Gbps traffic patterns from a single system, such as a server or storage device, communicating within site-to-site tunnels. These single-tunnel, single-elephant flow use cases have never had practical ...

  • Posted to: TechPost Blogs

    How AI agents, connected via the open-source Model Context Protocol (MCP) server, can simplify and standardize network automation tasks on Junos OS devices (e.g., retrieving configurations, checking device health, provisioning) with natural-language prompts. It further presents a lab-proof-of-concept showing the set-up of the Junos MCP Server (e.g., ...

  • Posted to: TechPost Blogs

    Red Hat Ansible Automation Platform and Juniper Networks each have collections of Ansible modules for managing Junos devices. We are merging Ansible’s collection into the Juniper Collection to provide a single collection of modules for our customers. Introduction The most important goal during the merger of our collections was ...

Top Contributors of the Week

Want more?

We’re all about connections, so make it easy for you to hop over to your favorite social channels.

Github

Collaborate on Juniper projects with developers worldwide. 

See more

vLabs

Use pre-built topologies to explore our products and solutions—all for free.

See more